These are the Chrysler Voyager dashboard warning lights, fourth generation (Mk 4, 2001–2007). All Chrysler Voyager warning lights are detailed below, plus what action to take when a warning light comes on.
|Symbol||Warning Light Description / Action|
The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position.
|2.||Low Fuel Light
When the fuel level reaches approximately 3.0 gallons (11.0 liters) this light will turn on and remain on until fuel is added.
This light turns on if the liftgate is not completely closed.
|4.||Door Ajar Light
This light turns on if a door is not completely closed.
Indicates vehicle speed.
|6.||Brake System Warning Light
This light monitors various brake functions,including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, there is a low brake fluid level or there is a problem with the anti-lock brake system. The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. Failure of either half of the dual brake system is indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.
The light may flash momentarily during sharp cornering maneuvers which change fluid level conditions. The vehicle should have service performed. If brake failure is indicated, immediate repair is necessary.
Vehicles equipped with Anti-Lock brakes (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required.
The operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approximately four seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer.The light also will turn on when the parking brake is applied with the ignition switch in the ON position.NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application.
This light turns on and remains on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the light is not on during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible.
This light monitors the Anti-Lock Brake System. The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS light does not turn on when the Ignition switch is turned to the ON position, have the light inspected by an authorized dealer.
The red segments indicate the maximum permissible engine revolutions-per-minute (r.p.m. x 1000) for each gear range. Before reaching the red area, ease up on the accelerator.
This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained.
|11.||Seat Belt Reminder Light
The light will turn on when the ignition switch is turned to the ON position as a reminder to “buckle up”. The light will remain on until the driver’s seat belt is buckled.
|12.||Engine Temperature Warning Light
This light warns of an overheated engine condition. If the engine is critically hot, a continuous chime will sound for 4 minutes. After the chime turns off, the engine will still be critically hot until the light turns off.
|13.||Vehicle Theft Alarm Light
This light will flash for approximately 15 seconds when the vehicle theft alarm is arming.
The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range.
Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, and you hear continuous chimes, turn the engine off immediately, and call for service.
|15.||Washer Fluid Light
This light turns on when the washer fluid level falls below approximately 1/4 filled. The light will remain on until fluid is added.
|16.||Transmission Range Indicator
This vacuum fluorescent display indicator shows the automatic transaxle gear selection.
|17.||Oil Pressure Warning Light
This light shows low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for 4 minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood.
|18.||Malfunction Indicator Light (Check Engine)
This light is part of an on board diagnostic system called OBD that monitors engine and automatic transmission control systems. The light will illuminate when the key is in the ON position before engine start. If the bulb does not come when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap,poor fuel quality, etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations the vehicle will drive normally and will not require towing. The Malfunction Indicator Light flashes to alert to serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs.
|19.||Trac Off Indicator
This vacuum fluorescent display indicator should illuminate for approximately four seconds as a bulb check when the ignition switch is first turned ON. The “TRAC OFF” Indicator will flash if the traction control is in use. The “TRAC OFF” Indicator will illuminate if:
• The Traction Control switch has been used to turn the system OFF.
• There is a Traction Control System malfunction.
• The system has been deactivated to prevent damage to the brake system due to overheated brake temperatures.
Extended heavy use of Traction Control may cause the system to deactivate and turn on the TRAC and the OFF indicators located in the instrument cluster. This is to prevent overheating of the brake system and is a normal condition. The system will remain disabled for about 4 minutes until the brakes have cooled. The system will automatically reactivate and turn off the TRAC and the OFF indicators. If your vehicle becomes stuck in mud, ice, or snow, turn the Traction Control System OFF before attempting to“rock” the vehicle free.
The odometer shows the total distance the vehicle has been driven. The trip odometer shows individual trip mileage. To switch from odometer to trip odometer, press the Trip Odometer button.
This vacuum fluorescent display indicator shows that the Speed Control System is ON.
|22.||Trip Odometer Button
Press this button to change the display from odometer to trip odometer. The word TRIP will appear when in the trip odometer mode. Push in and hold the button for two seconds to reset the trip odometer to 0 miles or kilometers. The odometer must be in trip mode to reset.
|23.||Tire Pressure Monitor Warning Light
This light will turn on when there is a Low tire pressure condition. The light will also turn on if a problem exist with any tire sensor. The light will remain on until the tire pressure is properly set or the problem with the sensor is corrected. This light will turn on momentarily as a bulb check when the engine is started.
When the tire pressure monitoring system warning light is lit, one or more of your tires is significantly under-inflated. You should stop and check your tires as soon as possible, and inflate them to the proper pressure as indicated on the tire and loading information placard. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Each tire, including the spare, should be checked monthly when cold and set to the recommended inflation pressure as specified in the tire and loading information placard.
|24.||Turn Signal Indicators
The arrow will flash with the exterior turn signal when the turn signal lever is operated. If the vehicle electronics sense that the vehicle has traveled about one mile with the turn signals on, a chime will sound to alert you to turn the signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb.
|25.||High Beam Light
This light shows that the headlights are on high beam. Pull the turn signal lever towards the steering wheel to switch the headlights from high or low beam.
1 thought on “Chrysler Voyager Dashboard Warning Lights”
excellent info – thankyou